I have my Kenmore refrigerator but i didn’t know about Kenmore ice maker reset switch .

Then i faced the issue in my Kenmore ice maker.

And then i learnt about it and i fixed the issue by myself.

You are also facing the same problem in your Kenmore refrigerator ice maker right ?

Okk don’t worry for that.

Now you are at the right place .

Just because I’m here with you .

And i promise you to solve your every single problem.

And in this article i have completely explained about the Kenmore ice maker reset button issues.

So let’s dive into in – depth informations about  the Kenmore ice maker reset.

kenmore ice maker reset

You are using the Kenmore refrigerator right ?

But before you start works you must have to know about reasons of the resetting of your Kenmore ice maker.

When your Kenmore ice maker not working properly then in this case you need to reset your Kenmore ice maker.

And here are the major reasons for which you need to reset your Kenmore ice maker.

Reasons :

1. Ice maker not working
2. Ice maker not producing ice cube
3. Low qualities ice production
4. Ice maker producing small ice cube
5. Ice maker producing hollow ice cube
6. Ice producing efficiency is very slow
7. Leaking water from ice maker
8. Error code indication

These are the major issues in your ice maker so for this issue you must allow your Kenmore ice maker reset to fix these issues.

So to fixing this issue in your Kenmore ice maker you must have to follow up the given Steps .

The steps are given below.

Solutions :

1. Firstly you must have to make sure that the power supply is perfectly working.
2. Plug in the power supply cord in the power board and switch on the power supply switch to the Kenmore refrigerator.
3. Then check and make sure that all door switches are working properly.
4. Then open the door of your Kenmore refrigerator.
5. Then now remove the covering and the ice tray from the Kenmore refrigerator.
6. In some models of the ice maker you get the button to remove the covering and the ice tray so you must have to be ware for that as per your Kenmore refrigerator model.
7. Then remove the Kenmore ice maker by removing the screws by multi bit screwdriver.
8. And then unplug the power supply couplers wire connector of the ice maker.
9. Now it’s cleared that the power supply is completely disconnected from the ice maker.
10. And then now wait for few minutes about of 5 minutes so that all the internal components get reset well.
11. Then now reconnect the power supply couplers wire connector of the ice maker.
12. And then set the ice maker at the position and screw it tighten by the multi bit screwdriver.
13. Then switch ON the power switch of the ice maker ( it’s located either at front or side of the ice maker).
14. Then locate the reset button of the Kenmore ice maker.
15. And then press the reset button for 3 to 5 seconds until you listen a clicking sound from it.
16. And look now your Kenmore ice maker is working perfectly.

This is the best easiest way to fix the issue when your Kenmore ice maker reset is needed.

 

You must watch this video tutorial for best results and understanding.

Kenmore ice maker reset button location

Most of the Kenmore refrigerator ice maker users don’t know about the Kenmore ice maker reset button.

And due this reason they can’t reset their Kenmore ice maker.

And they face the very bad problematic situations .

So if you also don’t know the location of the Kenmore refrigerator ice maker reset button.

Then just follow this steps you can find out the reset button of Kenmore ice maker.

Solutions :

1. Just open the Kenmore refrigerator door.
2. Then look at the front of the Kenmore ice maker that the switch is locating that’s not the reset button (that’s the power supply/ON OFF switch of the Kenmore ice maker).
3. So then you must have look at the under portion or the ice maker .
4. There under the ice maker appliance you can see a switch that’s the switch is the RESET BUTTON of the Kenmore ice maker.

By following these steps you can get the reset button easily for the Kenmore ice maker reset switch button. It same as the ge ice maker.

Kenmore ice maker troubleshooting

The troubleshooting of the Kenmore ice maker is pretty simple.

If you don’t have any idea then you must have to follow the given instructions step by step.

Solution :

1. You must have to confirmed that the power supply system is working perfectly.
2. Then check for the control panel display system of Kenmore refrigerator is working perfectly.
3. Then now check for the water supply line for any clogged and kinked and broken.
4. If you get the any clogged then you must have to make it clear and for the broken line it needs to be replaced.
5. Then check for the water filter for any Defect.
6. If your water filter is clogged or it’s more old than 6 months then you must have to replace the water filter for the best result.
7. Then now check in the water inlet valve Defects .
8. If the water inlet valve is clogged or broken and the water is leaking from it then you must replace the water inlet valve.
9. And then now open the door of the Kenmore refrigerator.
10. Amd then remove the covering and ice tray of the Kenmore ice maker.
11. And then remove the Ice maker by removing the screws by multi bit screwdriver .
12. And then unplug the power supply couplers wire connector of the ice maker .
13. Now you must have to defrost the ice maker completely and remove the ice molded and jammed ice.
14. And make sure that the ice maker filler tube should be cleared and working perfectly.
15. And then now set the ice maker back at the place and plugin the couplers wire connector.
16. And then screw it tighten.
17. Then now check the water pressure of the ice maker at the water inlet valve.
18. If the water pressure is less than 40 PSI then replace the water inlet valve and set the water pressure at between 40 to 120 PSI.
19. And then now you must have to set the temperature of the refrigerator at 37°F and the freezer at between 0°F to 5°F(-15°C to -18°C).
20. Then now switch ON the power switch the ice maker .
21. And then locate the reset button that’s at under portion of the ice maker.
22. And then now reset the ice maker by pressing the reset button for 3 seconds until you listen a beef sound.
23. And now set the covering and the Ice tray of the ice maker.
24. And now it’s done and Kenmore ice maker is working perfectly.

So this is the best way to troubleshoot your Kenmore refrigerator ice maker easily.

But to producing the best quality and hygienic ice cube you need to have a best quality of the ice maker or a refrigerator right ?.

But i have seen that most of the people don’t know to select the best quality of the ice maker and also the refrigerator.

And they choose the wrong model of the ice maker and refrigerators.

Due to which they get stucked in the very bad problematic situations in next.

So if you have need of the ice maker or the refrigerator then you must have to choose and select the best quality model.

And if you don’t have any idea to choose the best quality ice maker and refrigerator model then don’t worry for that.

I have suggested here the best quality of the models in the below for you.

Just because i have been using the same model in my kitchen .

And they’re providing me the best quality of services in my kitchen.

And also I’m suggesting these models not just because I’m using them but also the most of the professional experts suggest these models.

They provide you the best quality and facilities with modern advanced technology systems.

Best qualities and most advanced featured technology refrigerator.

I have been using this same model in my kitchen ..

And i have my own experiences to use that it’s really like a BOSS in the kitchen.

 

BUY NOW

 

FAQS –

 

 

Conclusion :

So in this today’s article i have completely explained about the Kenmore ice maker reset step by step .

If you have any more question in your mind then you must ask me in the comment section.

I would like to answer your questions Specifically.

And also if you know more informations about this topic of Kenmore ice maker reset then kindly requesting you to leave a comment .

Just because i would like to add your valuable informations in this article that helps others in better understanding.

 

Thank you.